Welcome

Freaduino Leonardo completely compatible Arduino Leonardo board

Item ID: FLEONARDO

Be the first to review this product

Availability: In stock

$23.95

Availability: In stock

$23.95

More Views

Details

Freaduino Leonardo completely compatible Arduino Leonardo board for sale-- Worldwide free shipping

Freaduino Leonardo completely compatible Arduino Leonardo board for sale-- Worldwide free shipping


Freaduino Leonardo Description:

Freaduino Leonardo is an Arduino Leonardo 100% compatible board. It is based on Arduino Leonardo design. So you can use Freaduino Leonardo as Arduino Leonardo. All code, shield and IDE for Arduino Leonardo are also valid on Freaduino Leonardo. 

Some visible improvement on hardware make Freaduino more flexible and easier to use. For example: 3.3v or 5v IO selectable allow you connect some 3.3v modules (such as XBee) to Freaduino directly. Using miniUSB interface, SPI bus breakout make bus connect easier.

The Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. 

The Leonardo differs from all preceding boards in that the ATmega32u4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Leonardo to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port. It also has other implications for the behavior of the board; these are detailed on the getting started page. 

Freaduino Leonardo completely compatible Arduino Leonardo board

 

Freaduino Leonardo  Application Ideas:

Serial Mouse and Keypad.
Led display/LCD controller.
Pulse width modulation driver.
Robot controller.
Data acquisition systems.
Alarm systems.
Programmable logic controllers.
Embedded Webservers.
Control Systems.


Freaduino Leonardo  Features:

Inherits all of Arduino Leonardo's features.
3.3V/5V Operating Voltage selection.
All pins out for Sensor and Servo.
SPI/IIC interface breakout.
Compatible to Arduino UNO/Duemilanove’s pin layout, screw hole and dimensions.

Freaduino Leonardo completely compatible Arduino Leonardo board - Worldwide free shipping

 


Freaduino Leonardo  Specification:

Microcontroller: ATmega32u4.
Operating Voltage: 5V.
Input Voltage (recommended): 7-12V.
Input Voltage (limits): 6-20V.
Digital I/O Pins: 20.
PWM Channels: 7.
Analog Input Channels: 12.
DC Current per I/O Pin: 40 mA.
DC Current for 3.3V Pin: 50 mA.
Flash Memory: 32 KB (ATmega32u4) of which 4 KB used by bootloader.
SRAM: 2.5 KB (ATmega32u4).
EEPROM: 1 KB (ATmega32u4).
Clock Speed: 16 MHz.

Freaduino Leonardo  Pin definition and Rating:

Power:
The Arduino Leonardo can be powered via the micro USB connection or with an external power supply. The power source is selected automatically.

External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the board's power jack. Leads from a battery can be inserted in the Gnd and Vin pin headers of the POWER connector.

The board can operate on an external supply of 6 to 20 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts and the board may be unstable. If using more than 12V, the voltage regulator may overheat and damage the board. The recommended range is 7 to 12 volts.

Freaduino Leonardo The power pins are as follows:

VIN. The input voltage to the Arduino board when it's using an external power source (as opposed to 5 volts from the USB connection or other regulated power source). You can supply voltage through this pin, or, if supplying voltage via the power jack, access it through this pin.
5V. The regulated power supply used to power the microcontroller and other components on the board. This can come either from VIN via an on-board regulator, or be supplied by USB or another regulated 5V supply.
3V3. A 3.3 volt supply generated by the on-board regulator. Maximum current draw is 50 mA.
GND. Ground pins.
IOREF. The voltage at which the i/o pins of the board are operating (i.e. VCC for the board). This is 5V on the Leonardo.

Memory:
The ATmega32u4 has 32 KB (with 4 KB used for the bootloader). It also has 2.5 KB of SRAM and 1 KB of EEPROM (which can be read and written with the EEPROM library).

Freaduino Leonardo  Input and Output:

Each of the 20 digital i/o pins on the Uno can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5 volts. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have

specialized functions:

Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial data using the ATmega32U4 hardware serial capability. Note that on the Leonardo, the Serial class refers to USB (CDC) communication; for TTL serial on pins 0 and 1, use the Serial1 class.
TWI: 2 (SDA) and 3 (SCL). Support TWI communication using the Wire library.
External Interrupts: 2 and 3. These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details.
PWM: 3, 5, 6, 9, 10, 11, and 13. Provide 8-bit PWM output with the analogWrite() function.
SPI: on the ICSP header. These pins support SPI communication using the SPI library. Note that the SPI pins are not connected to any of the digital I/O pins as they are on the Uno, They are only available on the ICSP connector. This means that if you have a shield that uses SPI, but does NOT have a 6-pin ICSP connector that connects to the Leonardo's 6-pin ICSP header, the shield will not work.
LED: 13. There is a built-in LED connected to digital pin 13. When the pin is HIGH value, the LED is on, when the pin is LOW, it's off.
Analog Inputs: A0-A5, A6 - A11 (on digital pins 4, 6, 8, 9, 10, and 12). The Leonardo has 12 analog inputs, labeled A0 through A11, all of which can also be used as digital i/o. Pins A0-A5 appear in the same locations as on the Uno; inputs A6-A11 are on digital i/o pins 4, 6, 8, 9, 10, and 12 respectively. Each analog input provide 10 bits of resolution (i.e. 1024 different values). By default the analog inputs measure from ground to 5 volts, though is it possible to change the upper end of their range using the AREF pin and the analogReference() function.

There are a couple of other pins on the board:

AREF. Reference voltage for the analog inputs. Used with analogReference().
Reset. Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the board.

Freaduino Leonardo Package List:

1 x Freaduino Leonardo
1 x miniUSB cabLe

Freaduino Leonardo completely compatible Arduino Leonardo board Packing include

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Write Your Own Review

Only registered users can write reviews. Please, log in or register